Millipore MAS-100 CG EX Air Sampling System, Sampling Heads Explosion Proof 9486

Millipore MAS-100 CG EX Air Sampling System, Sampling Heads Explosion Proof 9486R In good cosmetic condition. Powers on, buttons and digital screen respond well to input when plugged in to the charger. Even with fully charged battery system does not show battery charged. Unable to test further. See pictures for more detail. Only items pictured are included. The Charger is NOT included but shown in pictures to demonstrate that the system works with charger attached. Manufacturer: Millipore Sigma Model: MAS-100 CG EX Also Includes: x3 Sampling Head Mas-100 CG EX (CGSH5420B) x3 Braided Lines for a Air Sampling x5 Clamps Stainless Steel Tri-clamp Fittings x3 O-rings x1 Elbow x3 C-14435 BN2 HN 318008 3/8" Connector Specifications: (These specifications were taken from an online user manual and may not be specific to listed item.) The MAS-100 CG Ex Air Sampler is for use when there is a need to test compressed gases for microbial contamination. System approved for use in Zone 2 explosion hazard areas for safe, easy and accurate compressed gas sampling Airflow 100/50 standard liters per minute Application range 1.5 to 10 bar (absolute) Rechargeable battery pack Housing made from powder-coated aluminum Sampling head can be sterilized Explosion-proof in accordance with EU Directive 2014/34/EU (ATEX) Nominal Flow Rates: 100 liter/min. 5.0% (over the pressure range) of 1.5 bar to 10 bar (absolute) 50 liter/min. 5.0% over the pressure range of 1.5 bar to10 bar (absolute) Standard Sampling Volumes: 50, 100, 250, 500, 1000 liter Freely definable sampling volumes: 1 to 2000 liter, volumes individually selectable between 0 and 2000 liters. Pre-programmed gas types: Air, nitrogen, carbon dioxide, argon Battery Pack: 20 cells NiMH, 3800mAh, voltage 24 V Battery Charger: 110-240 Volt, 50-60 Hz Charger Input: 36 V DC, 1.5 A DisplayAlphanumeric liquid crystal display, 32 characters Lifetime RTC Battery: Approx. 10 years Flow Valve: Proportional, 24 Volt Processor Type: 80C552 Gas Regulation: Mass flowmeter and pressure sensor 0-10 bar and proportional valve Sampling Head Head without Clamps, Height: 16.0 cm Diameter: 10.0 cm Weight: 1.5 kg Material: Anodized aluminum, clamps of stainless steel Autoclavable: 20 minutes at 121C TubingLength: 1.5 m ID=10 mm OD=19 mm, sterilize for 20 min at 121C Rapid Connectors: Chromium-plated brass Dimensions Actual Dimensions: 21x18x5" Case Dimensions: 18x25x11" Actual Weight(with Case): 48 lbs Sold as is with 30day Right of Return, only pictured items included Easy return/refund for any reason Anacapa Equipment RETURNS Anacapa Equipment Brokers, Inc. (Seller) strives to offer excellent customer service. You may return any equipment purchased from us for any reason within thirty (30) days after your receipt of the equipment for a full refund of the purchase price, provided that returned items are received in the same condition as sent. We DO NOT ship internationally. If you are using a freight forwarder then returns are VOID. SHIPPING All equipment purchased is shipped within one (1) business day (subject to freight availability) after receipt of payment and is shipped FOB place of shipment. We only charge actual shipping cost. If eBay overcharges for shipping, we issue an immediate refund for the difference. If you are undercharged, we will absorb the cost. We DO NOT ship internationally. IF you are using a freight forwarder then returns are VOID. LIMITED WARRANTY Buyer acknowledges that the equipment is being sold as is" and without any warranty of merchantability or fitness for a particular use. The entire risk as to the quality and performance of the equipment is with the Buyer. Should the equipment prove defective following its purchase the Buyer and not the Seller, manufacturer, distributor, or retailer assumes the entire cost of all necessary servicing or repair. Buyer may inspect the equipment prior to purchase and placement of the order. Failure to inspect prior to placement of an order is deemed a waiver of Buyers right to inspect. Buyer is responsible for determining the suitability of the equipment for its application. Seller assumes no liability for the use or misuse of any equipment purchased by Buyer. It is assumed that the equipment will be installed and operated by qualified personnel. The Buyer agrees that the Seller shall not be held responsible or liable for any injuries or damages, whether incidental or consequential, associated in any way with the equipment purchased. The Buyer, by purchasing this equipment, indicates its acknowledgment of, and agreement, to the terms of this limited warranty . INDEMNITY Buyer shall be solely liable for, and shall defend, indemnify, and hold Seller, its Affiliates, and all of their respective directors, officers, employees, agents, and independent contractors (Indemnitees) harmless from and against any and all damages, liabilities, injuries, losses, costs (including reasonable attorneys and experts fees at trial and on appeal), and expenses which may be incurred by, asserted against, or recoverable from any Indemnitee as a result of any actual or threatened action, suit or proceeding arising out of or relating in any way to the purchase of equipment from Seller. The validity and interpretation of this Agreement and the enforcement thereof shall be governed by the laws of the State of California without regard to any principles governing conflicts of laws. Any dispute arising from the purchase of equipment from Seller must be resolved in the State Courts of California.