Newport ESP301-2N 2 Axis Motion Controller, USB, GPIO USED (9726)R

No longer available

Newport ESP301-2N 2 Axis Motion Controller, USB, GPIO USED (9726)R

$2,250 (USD)

Available quantity: 4

Goleta, CA

Description

Newport ESP301-2N 2 Axis Motion Controller, USB USED (9726)R In good cosmetic condition. Powers on, buttons and digital screen respond well to input. See pictures for more detail. Manufacturer: Newport Model: ESP301-2N Type: 2 Axis Also Includes: Power Cable Specifications: The following specifications were taken from an online user manual or manufacturer's website and may not be specific to this item, please look at pictures carefully for items included and specifics. These specifications are for reference only. Number of Axis: 2 axis of any combination of DC servo and 2-phase stepper motors Computing Power: 400 ms servo cycle up to 3 axis 64 bits floating point DSP, with a peak performance of 1200 MFLOPS Digital PID servo loop with velocity and acceleration feed forward Motion: Trapezoidal and s-curve velocity profile Synchronized and non-synchronized point-to-point Jogging, Continuous moves 3D Linear interpolation, 2D Circular Interpolation Master-slave, Electronic gearing On-the-fly changes of target position, speed, acceleration, and PID Contouring: 2D Contouring with continuous buffer loading External Event Synchronization: Program execution depending on TTL I/O status Operating Modes: Real-time command execution via computer interfaces Stand-Alone Execution of Programs Front panel manual motion command execution Programming: 100+ intuitive, 2 letter ASCII commands Command set includes: User defined units, software limits, home search (with and w/o top zero), linear error and backlash compensation, etc. Typical time to send a command and to read the response: RS-232-C: 7-30 ms; USB: 3.5 ms; IEEE-488-1: 1 ms Memory: 64KB Flash Non-Volatile User Program Memory (last for approx. 6,000 commands) Front Panel Display: Backlit LCD display, 4 lines x 20 characters, 21 mm x 70 mm Motor Control: DC brush motors at 48 V, 3 A max. Closed-loop operation 16-bit DAC resolution 5 MHz max. encoder input frequency Stepper Motor Control: 2-phase stepper motors at 48 V, 3 A max. Open- or closed-loop operation 10 kHz commutation rate 1000x max. (programmable) micro-step resolution Total Available Motor Power: 150 W, 48 V, 3 A max per axis 5 Hz (Gain range 7) Dimensions Actual Dimensions: 13x17x5" Actual Weight: 13 lbs Sold as is with 30day Right of Return, only pictured items included Easy return/refund for any reason Anacapa Equipment RETURNS Anacapa Equipment Brokers, Inc. (Seller) strives to offer excellent customer service. You may return any equipment purchased from us for any reason within thirty (30) days after your receipt of the equipment for a full refund of the purchase price, provided that returned items are received in the same condition as sent. We DO NOT ship internationally. If you are using a freight forwarder then returns are VOID. SHIPPING All equipment purchased is shipped within one (1) business day (subject to freight availability) after receipt of payment and is shipped FOB place of shipment. We only charge actual shipping cost. If eBay overcharges for shipping, we issue an immediate refund for the difference. If you are undercharged, we will absorb the cost. We DO NOT ship internationally. IF you are using a freight forwarder then returns are VOID. LIMITED WARRANTY Buyer acknowledges that the equipment is being sold as is" and without any warranty of merchantability or fitness for a particular use. The entire risk as to the quality and performance of the equipment is with the Buyer. Should the equipment prove defective following its purchase the Buyer and not the Seller, manufacturer, distributor, or retailer assumes the entire cost of all necessary servicing or repair. Buyer may inspect the equipment prior to purchase and placement of the order. Failure to inspect prior to placement of an order is deemed a waiver of Buyers right to inspect. Buyer is responsible for determining the suitability of the equipment for its application. Seller assumes no liability for the use or misuse of any equipment purchased by Buyer. It is assumed that the equipment will be installed and operated by qualified personnel. The Buyer agrees that the Seller shall not be held responsible or liable for any injuries or damages, whether incidental or consequential, associated in any way with the equipment purchased. The Buyer, by purchasing this equipment, indicates its acknowledgment of, and agreement, to the terms of this limited warranty . INDEMNITY Buyer shall be solely liable for, and shall defend, indemnify, and hold Seller, its Affiliates, and all of their respective directors, officers, employees, agents, and independent contractors (Indemnitees) harmless from and against any and all damages, liabilities, injuries, losses, costs (including reasonable attorneys and experts fees at trial and on appeal), and expenses which may be incurred by, asserted against, or recoverable from any Indemnitee as a result of any actual or threatened action, suit or proceeding arising out of or relating in any way to the purchase of equipment from Seller. The validity and interpretation of this Agreement and the enforcement thereof shall be governed by the laws of the State of California without regard to any principles governing conflicts of laws. Any dispute arising from the purchase of equipment from Seller must be resolved in the State Courts of California.

Specifications

ManufacturerNewport
ModelESP301-2N
ConditionNew
Type2 Axis
Also includesPower Cable
SpecificationsThe following specifications were taken from an online user manual or manufacturer's website and may not be specific to this item, please look at pictures carefully for items included and specifics. These specifications are for reference only.
Number of axis2 axis of any combination of DC servo and 2-phase stepper motors
Contouring2D Contouring with continuous buffer loading
External event synchronizationProgram execution depending on TTL I/O status
Command set includesUser defined units, software limits, home search (with and w/o top zero), linear error and backlash compensation, etc.
Memory64KB Flash Non-Volatile User Program Memory (last for approx. 6,000 commands)
Front panel displayBacklit LCD display, 4 lines x 20 characters, 21 mm x 70 mm
Total available motor power150 W, 48 V, 3 A max per axis
Actual dimensions13x17x5"
Actual weight13 lbs